请使用微信扫描此二维码

您微信暂未注册或绑定账号

注册账号

或

绑定账号
立即注册
82
Views
0
Comments

NT UpSweep

NT UpSweep
0
Version: 1.0.0 Install
Plugin Information
Ratings:
0
Plugin Category
Line/Face
Uploader:
zfjoy520
Release date:
2026-11-19 19:20
Update date:
2026-11-20 16:49
current version:
1.0.0
Command numbers:
5
File size:
3.29 KB
Introduction
Sweep along the path to maintain a vertical contour, generating railings, lines, and decorative moldings.

The standard Follow Me operation will rotate the contour when the direction changes, resulting in unwanted distortion. NT upright following keeps the selected contour vertical as it travels along the guiding path.

Railings, curbs, lines, and decorative moldings often extend along complex three-dimensional paths, but must maintain vertical alignment. NT upright following helps architects and 3D modelers to outline and stretch the cross-sectional profile along the guiding path, avoiding common accidental rotations following the standard path. It is suitable for landscape curbs, stair handrails, ramp guardrails, eaves, and customized architectural details.

Keep vertical
The contour always maintains vertical alignment and does not twist when traveling along the selected path.

Support curved path
Stretching along the arc and connected curves to meet the actual design element requirements.

Ramp workflow
Generate continuous shapes along ramps, stairs, and variable elevation paths.

Clear contour control
Start scanning directly based on the contour surface of the defined section.

Building purpose
Quickly create railings, curbs, lines, and decorative moldings with fewer corrections.


NT UpSweep(NT UpSweep)
Select the contour surface and connected path edges, and sweep along the path to generate a solid.

NT UpSweep Vector From Edge(NT UpSweep Vector From Edge)
Select an edge and set its direction as a vertical vector.

NT UpSweep Vector Coordinates(NT UpSweep Vector Coordinates)
Directly specify the vertical vector through X/Y/Z coordinates.

NT UpSweep Reset Vertical(NT UpSweep Reset Vertical)
Restore the vertical vector to the default Z-axis direction.

NT UpSweep Settings(NT UpSweep Settings)
Set default parameters for end caps, softening/smoothing, and preserving path edges.
Developer: Nice Tower  Visit the developer's site>  
Version1.0.0New command
更新日志:
[2026.11.19] 首发 v1.0.0,界面全面汉化;提供扫掠、从边定义矢量、输入坐标、重置竖直与设置共五个命令。
Comment
No comment!


Note: You can comment if you are using the plugin.


Click stars Rating:
Your comment content:
My Plugin Library
More from this Uploader:
zfjoy520
0
zfjoy520
0
Who Browsed Also Browsed:
5
(1)
3
(1)
4.5
(2)
zfjoy520
0
Who Installed Also Installed:
zfjoy520
0
zfjoy520
0
zfjoy520
0
zfjoy520
0
在
线
咨
询
在线咨询
小P在线时间周一至周五9:00-18:00,下班时间请先查看常见问题↑↑
微信扫码联系我们

微信扫码联系我们

扫码关注
建模无敌

SUAPP插件库| 简体中文|繁體中文|English Version|

Copyright © 2008 - 2026 SUAPP插件库 All rights reserved.( 蜀ICP备19001322号   川公网安备51010702043892号 )

GMT+8, 2026-11-23 07:05 , Processed in 0.034758 second(s), 9 queries , Gzip On, MemCache On.

返回顶部